MWF GE SmartWater Side-by-Side refrigerator filter.

General Electric MWF filter fits General Electric and Hotpoint side-by-side refrigerators with a round, plastic, white filter, mounted inside the refrigerator on top of the upper shelf.

GWF
GWFA
GWF01
GWF06
MWFA
HWF
HWFA

Specifications of GE MWF:

- Operating Temperature:	Min. 0.6°C / Max. 38°C
- Working Pressure:	Min. 2.8 bar / Max. 8.3 bar
- Flow Rate:	1.9 Lpm
- Capacity:	1135 liter
- Service Life:	6 months
- Dimensions:	13x8.5cm

Fridge waterfilter MWF GE SmartWater filter [MWF] Fits the following refrigerators models:
GE
GC23LDC	GC23LGB	GC23LMA
GC23LMC	GC23LMG	GC23LSS
GC23MSS	GCE21MGTFBB	GCE21XGYFBB
GCE21XGYFWW	GCE23LGTFAV	GCE23LGTFBG
GCE23LGTFLS	GCE23LGWFBB	GCE23LGWFSS
GCE23LGWFWW	GCE23LGYFLS	GCE23LGYFLV
GCE23LGYFSS	GCE23LGYFWW	GCU21XGYFBB
GCU23LGYFSS	GCU23LGYFWW	GIE21LGWFBB
GIE21MGTFBB	GSE22KEWFWW	GSE25KEWFWW
GSE25MGTCWW	PC23HB	PC23HEL
PC23HF	PC23HSS	PC23NB
PC23NCO	PC23NCOB	PC23NCOGB
PC23NEL	PC23NF	PC23NM
PC23NSS	PC23NW	PC23NZM
PCE23NGTCFSS	PCE23TGXFSS	PCE23VGXFBB
PCE23VGXFSS	PHE25TGXFBB	PHE25YGXFWW
PI23NB	PI23NBS	PJE25YGXFSS
PSE25VGXCSS	PSE27NHWCSS	PSE27VGXFBB
PSE27VHXTWW	PSE29NHWCSS	PSE29VHXTBB

Installing GE MWF Waterfilter:

Removing the Filter Cartridge:
The waterfilter cartridge is located in the back upper right corner of the refrigerator compartment.
If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

Installing the Filter Cartridge:
1.
There's an adaptor attached to the top of the new filter cartridge.
If you are replacing a SmartWater cartridge, the adapter must be removed before installing the cartridge. To remove the adaptor, turn it to the left about 1/4 turn.
If you are replacing a Waterfilter by Culligan cartridge, leave the adaptor in place. This adaptor will stay in the refrigerator when you replace future cartridges.
2.
On models without a replacement indicator light, apply the month and year sticker to the new cartridge to remind you to replace the filter in six months.
3.
Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.
4.
Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder.
5.
Slowly turn it to the right until the filter cartridge stops. Do not overtighten ! As you turn the cartridge, it will automatically raise itself into position. The cartridge will move about a 1/2 turn.
6.
Run water from the dispenser for 3-4 liters (about 3 minutes) to clear the system and prevent sputtering.
7.
Press and hold the RESET WATER FILTER pad (on some models) on the dispenser for three seconds.